CE Intumescent Acrylic Sealant

Application: Linear joints and penetration seals Fire Resistance Period: 240 minutes Insulation/integrity: Integrity and insulation Test Standard: BS EN 1366-3 and BS EN 1366-4 Approval Type: CE Mark – 0843-CPR-0148, ETA 13/0659 & 13/0660
Pyroplex® CE Intumescent Acrylic is used to form linear gap seals were gaps are present in wall and floor constructions and linear joints where wall and floor constructions abut. The sealant can also be used to form a penetration seal around metallic pipes and electrical Cables to reinstate the fire resistance performance of wall and floor constructions, where they have been provided with apertures for the penetration of services.
Pyroplex® Intumescent Acrylic has slight intumescent properties that cause it to expand on exposure to elevated temperatures. The intended function of the sealant is to reinstate the fire resistance performance of fire compartment.
Pyroplex® CE Intumescent Acrylic can provide up to 240 minutes fire resistance integrity depending on application and backing material and has been tested to BS EN 1366-3 and BS EN 1366-4.
The intended use of Pyroplex® CE Intumescent Acrylic is to reinstate the fire resistance performance of:
The intended use of Pyroplex® CE Intumescent Acrylic is to reinstate the fire resistance performance of:
Linear Joints in rigid wall constructions – 100mm in thickness with sealant applied to both sides of the joint [unexposed and exposed] Double-sided Joint Configuration
Linear Joints in rigid wall constructions – 150mm in thickness with sealant applied to both sides of the joint [unexposed and exposed] Double-sided Joint Configuration
Linear Joints in rigid wall constructions – 200mm in thickness with sealant applied to both sides of the joint [unexposed and exposed] Double-sided Joint Configuration
Linear Joints in floor constructions – 150mm in thickness with sealant applied to top of floor only [unexposed face] Single-sided Joint Configuration
Linear Joints in floor constructions – 150mm in thickness with sealant applied to both sides of the joint [unexposed and exposed] Double-sided Joint Configuration
Linear Joints in flexible wall constructions – 110mm in thickness with sealant applied to both sides of the joint [unexposed and exposed] Double-sided Joint Configuration – Header Joints
Penetration Seals in Rigid Walls 150mm in thickness (min.)
Penetration Seals in Rigid Floors 150mm in thickness (min.)
Installation of system Pyroplex® CE Intumescent Acrylic shall be conducted as follows:
Linear Joint/Gap Seals
1. Wear Suitable protective clothing, skin and eye protection.
2. Ensure all surfaces are clean and dry.
3. Position appropriate backing material within the gap at the minimum depth to allow for the specified thickness of sealant.
4. Gun the sealant into the opening ensuring that the gap is fully filled and scrape away any excess material.
Penetration Seals 1. Tightly pack mineral wool backing material (nominal density kg/m2) within the opening and around the service(s), leaving a minimum 10mm depth to the plane of the floor/wall surface at both sides.
2. Gun the sealant onto both exposed faced of the mineral wool backing and around the service(s), ensuring that good contact is achieved with both the service(s) and sides of the opening. Scrape away excess material ensuring that a minimum 10mm thickness of sealant is achieved.
3. Tool the surface of the seal as required within 30 minutes of application using a wet spatula.
4. Clean tools using soap and warm water.
Pyroplex® CE Intumescent Acrylic has been tested to the requirements of BS EN 1366-4 & BS EN 1366-3
Providing the product is installed in accordance with the requirements of the guidance document the fire performance characteristics of the product is guaranteed for a period of 10 years.
CE Intumescent Acrylic
Certificate of Constancy of Performance 0843-CPR-0148
Linear Joints Decleration of Performance
Penetration Seals Decleration of Performance
ETA-13-0660
ETA-13-0659