Search 60+ Handrail Fittings from leading Stair Components & Balustrades manufacturers including; Access Technologies Ltd

You can see a full list of manufacturers of Handrail Fittings here.

Other popular types of Stair Components & Balustrades include; Stair Balustrade Systems, Stair Tread Covers and Stair Handrails.

Important criteria to consider when specifying Handrail Fittings include; Type and Manufacturing Method.

C18 Base Flange - Intergrated Toeboard

Access Technologies Ltd
The Base Flange with Integrated Toeboard is ideal for guardrailing and balustrading applications where the addition of a toeboard is required. The side plates have slotted holes to allow for a degree of sideways movement for ease of installation. It is recomme...

BC05 Swivel Elbow

Access Technologies Ltd
Type BC05 fitting has been designed as a variable angle in-line connection, adjustable through 202° Warning!: An entire structure should not be constructed from type BC05 or any other swivel fitting, as these would not provide sufficient stability or rigidit...

C12 Railing Base Flange - Ductile

Access Technologies Ltd
The Railing Base is designed to provide a base for railings and other structures. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Page ...

C59 Angle Base Flange (11° to 30°)

Access Technologies Ltd
Similar to a type C53, it is used to set the upright angle between 11° - 30°. This fitting should only be subjected to light loads which cannot be positioned at 90°to the applied load. For greater loads or other tube sizes a type C12 flange should be used w...

C25 Short Tee Swivel

Access Technologies Ltd
Short Tee Swivel fittings are normally used in pairs to facilitate corner angles of 90° to 180°, it is also used on staircases with a C02 and C03 fittings in conjunction with a short piece of tube and a C65 Plastic Stop End in landing areas. When ordering ...

C29 Adjustable Short Tee (30° to 60°)

Access Technologies Ltd
The Adjustable Short Tee fitting will accommodate any rake angle from 30° to 60°. This fitting is commonly used for the top rail of handrail to accommodate the rake angle on slopes. It can also be used for any Tee Joint that needs to mate at an angle of be...

C35 Male Swivel

Access Technologies Ltd
The Male Swivel can be used on its own for use with a shakle and chain or with the C36 female swivel to mount rails at any angle for slopes. It can also be used for attaching flat sheets or boards to a structure and is available assembled with the C36 fittings...

C57 Three Socket 11° to 30° Tee

Access Technologies Ltd
Similar to a type C27, it is used on Safety Railing with slopes between 11° - 30° and fixes the top rail to a vertical intermediate upright. Unlike the type C27 these components are ex - stock and do not need machining....

C37 Double Male Swivel

Access Technologies Ltd
The Double Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings. The double swivel combination is also available assembled as a type C47 fitting....

C10G Swivel Base

Access Technologies Ltd
The Swivel Base is designed to provide a base fixing. It is usually used in conjunction with a C36G type fitting to make a C46G type base swivel combination. This fitting does not provide sufficient rigidity to be used as a railing base without other means...
Thnking face emoji
Did you know that the most common Type for products within the Handrail Fittings category are angle and double?

C24 4 Way Cross + Central Tube

Access Technologies Ltd
The 4 Way Cross tting provides a four way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting. This fitting may also be used for the top rail with the centre post capped with a C65 Plas...

C14 Railing Horizontal Side Support

Access Technologies Ltd
The Railing Horizontal Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our T...

C13 Railing Vertical Side Support

Access Technologies Ltd
The Railing Vertical Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Tec...

C40 90° Crossover

Access Technologies Ltd
The 90° Crossover connects two rails at 90° to each other and is often used for the handrailing when continuous standard lengths of tube are used. Please note that tube joints should use the C00 or C01 type fitting and not the C40 type fitting....

C04 Long Tee

Access Technologies Ltd
The Long Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. It allows the through tube to be joined inside the fitting. An alternative is the C03G type fitting....

C03 Short Tee

Access Technologies Ltd
The Short Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. If tubes need to be joined inside the fitting then a C04G type should be used....

C38 90° Corner Male Swivel

Access Technologies Ltd
The 90° Corner Male swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings to make a corner combination fitting which is also available assembled as a type C48 type fitting....

C06 Internal T Joint

Access Technologies Ltd
The Internal T joint is designed to provide an angled joint between a tube and a FastClamp fitting when used in conjunction with C02G and C03G type fittings. Often used for railing tops and midrails to accommodate a slope as offset railing....

CA40 Add On 90° Crossover

Access Technologies Ltd
The Add On 90° Crossover allows existing structures to be added to without the need for any dismantling. This fitting is designed to give a 90° offset crossover joint. Tubes must not be joined within this fitting....

C05A Variable Elbow (11° to 30°)

Access Technologies Ltd
The Variable Elbow is designed to make joints at an angle of between 11° and 30°....

1 specifier has shown an interest in this product the last month.

Thnking face emoji
Did you know that the most common Manufacturing Method for products within the Handrail Fittings category are stock

C28 Adjustable 2 Socket Cross 30°- 45°

Access Technologies Ltd
The Adjustable 2 Socket Cross fitting will accommodate any rake angle from 30° to 45°. This fitting is not recommended as the top fitting on a guardrail or balustrade system, use the C29 Adjustable Short Tee....

Handrail Fittings Building Products

Search 60+ Handrail Fittings from leading Stair Components & Balustrades manufacturers including; Access Technologies Ltd

You can see a full list of manufacturers of Handrail Fittings here.

Other popular types of Stair Components & Balustrades include; Stair Balustrade Systems, Stair Tread Covers and Stair Handrails.

Important criteria to consider when specifying Handrail Fittings include; Type and Manufacturing Method.